Floor Care
Available at
Hilltop Tool Rental
Jam Saw

13 amp motor.
6-1/2" diameter flush-cutting
blade.

   $38.50 / Day
Pullman-Holt Floor Machines

The B-Line Floor Machines are designed for professional floor care
maintenance including stripping, scrubbing, spray buffing, polishing,
sanding and grinding on hard floor surfaces, along with shampooing
and bonnet cleaning of carpeted floors. They are equipped with cool-
running large frame motors 1horsepower, with all steel planetary
gearboxes.

  • spread turning 175 rpm
  • Powder coated aluminum chassis is chip-resistant and corrosion
    resistant.
  • Star latch allows operator to adjust handle to any comfortable
    height, using either hand or foot.
  • Dual deadman switch system stops motor with release of trigger
    for operator protection.
  • Safety latch disables machines when not in use.
  • Non-marking 5 inch solid wheels.
  • Non-marring bumpers on chassis and motor canopy.
  • 50 foot power cord.
  • CSA certified models available.

13" - $38.50/day,  17" - $49.50/day, or
20" - $49.50/day
Sanding Drum 17" or 20"   $10.00 / Day
Sanding Pads and Paper
Description
Price
13" Floor Pad - Black
$7.32
17" Floor Pad - White
$10.81
17" Floor Pad - Black
$10.81
20" Floor Pad - Black
$14.32
17" Whole Floor Disc Grit 36
$10.24
17" Whole Floor Disc Grit 80
$7.06
17" Whole Floor Disc Grit 100
$6.95
20" Whole Floor Disc Grit 36
$14.88
20" Whole Floor Disc Grit 80
$9.81
20" Whole Floor Disc Grit 100
$9.11
2" Flooring Cleat Nailer
Model FCN200

Drives from 1-1/2" to 2" "L" shape cleat nails
Pneumatic driving action consistently drives fastener for better finished installation
Unit comes fully assembled and ready for use right out of the box
Strong, lightweight, die-cast aluminum construction
Non-Marring base is designed to allow driving of fastener close to wall
Better balance for stability - tool sits upright for smoother floor installation
Rear-load gravity fee magazine with a bypass pusher
Fitting is angled so hose does not interfere with magazine or operator
Ergonomic design with longer handle for easier use
Hardened driver blade for longer life
Provides better holding power while allowing the floor to contract and expand
Standard Equipment: Nailer, mallet, air tool oil, wrenches, 1/4" industrial male
plug, and operating manual

                                                           $38.50 / Day
Essex Silver Line
Model SL-8 Sander

Motor- 1 HP constant speed, 115 volt, AC only,
60 Cycle, single phase. Runs on 14 amps.
Drum- Standard 8” width, soft rubber cover with
aluminum drum core, spring loaded cam paper
locking system, takes 8 x 20 3/16” paper
Drum Speed - 1800 RPM, constant speed
Net Weight - 115 lbs.

Model SL-8V2
The Model SL-8V2 is the same powerful
machine as the SL-8 with the hook and loop
technology. Our new Hook & Loop Drum
incorporates hook and loop technology for
installation of paper. Hook on the drum
attached to the rubber, loop on the paper.

    
$75.00 / Day
Essex Silver Line
Model SL-7 Floor Edger

Motor - 1.5 HP Universal Motor, 115 volt, AC.
Disc Pad - 7" Diameter, rubber backed with
steel, precision balanced, 3600 RPM
Disc Guard - Free wheeling, non-marking
Vacuum - Oversized rerouted chamber for
extra-clean pickup.
Ball Bearings - On all revolving parts,
lubricated and sealed.
Net Weight - 30 lbs.
               
$65.00 / Day
Essex Silver Line
Model SL-1218OVS Orbital Sander
with Dust Containment

The design allows the DIYer to accomplish the work of a rotary
polisher without knowing how to run one!

Applications include:
  • Screening floors after sanding with the SL-8 & SL-7
  • Screen & recoating polyurethane floors
  • Waxed floors scrubbing & polishing
  • Wood deck sanding & refinishing
  • Parquet floor sanding & refinishing
  • New & pre-finished floor sanding & refinishing
  • Tile Maintenance

12" x 18" Orbital Polisher, 1hp, Cast Aluminum base with weight
protected from dust, fan cooled, thermal overload on motor, Heavy
Duty Rubber towers in four corners support the base & plate
protecting the motor shaft and allowing for easier operation. Larger
(5/8") orbital action, Armature has a 50lb pre-load to absorb shock
and start easier.
                     $65.00 / Day

12" x 18" Thick white pads       $8.95 each
EDCO 50200 Single-Disc Floor
Grinder

This Single-Disc Floor Grinder has 11" of working width that will grind
approximately 200-250 square feet per hour at 1/32" with EDCO
Dyma-Serts. The round shroud gets tight against walls with help
from easy-rolling 10" steel-core, rubber wheels. This grinder
features a lifting eye for easy loading and unloading, a 2" vacuum
port and water port, an accessory toolbox tray and side-mounted
lifting handles. This grinder includes one multi-accessory disc, which
accepts Dyma-Serts, Strip-Serts and all other grinder accessories.
Three grinding accessories are required per loading. This rugged
and easy to maintain grinder is equipped with a 25-foot power cord
attached with a cord hanger, easy access to grease fittings and a 30
pound standard weight pack. This single phase electric grinder is
ideal for residential applications, grinding concrete and areas less
than 1,500 square feet. The 1.5 horsepower provides ample power
to repair damaged concrete slabs, remove urethanes or epoxy think
coats and leveling high spots or surface imperfections. This 115/230
volt single-disc grinder can smooth rough surfaces, rain or trowel
marks, as well as remove mastics, thin-sets, paint build-ups, resins
and more.

                 $99.00/day

 3 Stones $21.00 per set
MOTOR
Engine Manufacturer                   Baldor     
Max. Horsepower                     1 1/2 HP     
Rated Horsepower                   1 1/2 HP     
Voltage                                           115V     
Phases                                          Single     
Cycles                                        60/1 Hz     
Full Load                                       14.4A     
Starting                                 79@115VA     

TRANSMISSION
Weight, Crated               53 kg / 116 lbs     
Weight, Uncrated           48 kg / 105 lbs     

BLADE DATA
Blade Guard Capacity     254 mm/10 in.     
Blade Shaft                             RPM 2760     
Max Depth of Cut 95 mm / 3 - 3/4 inch     
Arbor Size          16 mm/5/8 in.  
Engine/Motor
Engine Manufacturer                                Baldor
Max. Horsepower                                   1 1/2 HP
Rated Horsepower                                 1 1/2 HP
Voltage                                                       115 V
Phases                                                               1
Cycles                                                         60 Hz
Full Load                                                     14.4A
Starting                                                         80 A
Motor                                                    RPM 2760
Blade Data
Blade Guard Capacity                   254 mm/10 in.     
Blade Shaft                                           RPM 2760   
Max Depth of Cut                      95 mm/3 3/4 in.    
Arbor Size                                    16 mm/5/8 in.
Cutting Table Data
Cutting Head Cast Aluminum     
Cutting Table Cart of cast aluminum rides on extended
rails for longer cuts and two intermediate supports for
stability and consistent tracking; vulcanized top with      
aluminum rip guide.  
Features Galvanized Water Pan
Tile Saws
Short     $85.00 / day
Long    $125.00 / day
Pneumatic Tile
Stripper

Ergonomic design lets operator stand
upright eliminating backaches.
High-strength tubular handle and soft
foam hand grips for operator comfort.
Quick-change, hardened steel tool chuck
accepts dozens of accessories.
Requires only 6-8 CFM at 80-90 PSI.

  
$49.00 / Day
Knee Kicker

Telescoping steel tubes with five settings for
length.
Double-engagement buttons eliminate hole
elongation.
Wide head features 3 replaceable nap grips.
Replaceable square bumper is foam-filled, and
features a tough seamless, neoprene cover.

      
$20.00 / Day
Power Stretcher

Driving head has adjustable locking feature for
partial stretches.
3 standard size extension tubes
interchangeable with other popular models.
Includes the autolock tube.

               
$49.00 / Day
Heat Bond Kit

Teflon self-cleaning base.
air-cooled head shield.
Uniform heat.
Low profile

    
$20.00 / Day
Carpet Tape      $12.95
Vinyl Tile Cutter

Cuts any resilient tile including 18"
square slab tiles.
Offset base holds tile more securely.


 
$20.00 / Day
Vinyl Roller

Solid steel rollers provide long
trouble-free service.
Detachable handle.

$20.00 / Day
3-Stage Wet/Dry Vacuum Cleaner - Model 8925

A powerful mess needs a powerful vacuum cleaner. The Milwaukee
15 gallon stainless steel vacuum has a positive water shut-off to
protect the motor during wet pick-up situations. Heavy duty filters
can handle large pieces of material as well as dust. Model 8925
offers a 16 in. stainless steel tank and heavy duty casters. It also
features an external drain valve for easy water removal. With 9.2
amps, the 3-stage bypass motor can handle the rough stuff.

SPECIFICATIONS:
Voltage  120 AC                          Amps  9.2   
Material  Wet/Dry                       Capacity  15 Gal. / 2 Bu.   
Tank  Stainless                           Tank Dimensions  16 in. dia.
Motor Type  3 Stage Bypass       Max Air Flow  92 cu. ft./min.  
Sealed Suction in Water 134 in.  Height  41 in.   
Width  22 in.                               Tool Weight  63.0 lbs.   
Shipping Weight  74.0 lbs.  

INCLUDES:
1-1/2 in. O.D. Hose Connections         Cloth Filter
3 Hold-Down Clamps                           4-Wheel Caddie   
3 Paper Filter Bags                              Wire Frame Assembly  
Wet Pick-Up Conversion Pan               Swivel Connector   
Tool Bag  

                                 $49.50 / Day
Carpet Extractor

The Bext® Pro 100H features a 13 gallon solution tank which enables you to
tackle large jobs or easily maneuver in compact areas. Equipped with exclusive
circuit finder technology on heated models, the Bext Pro easily identifies when
the machine is plugged into separate circuits.

Features
•  Instant, continuous heating of 212° solution attacks tough carpet stains
•  Two pressures—100 psi and 400 psi—allow for enhanced cleaning flexibility
•  Three models, with heated and non-heated performance, are available to satisfy
applications ranging from simple carpet restoration to deep extraction
•  Clam shell design allows for easy equipment access and maintenance
•  CRI Seal of Approval ensures a safe, sustainable cleaning solution

                                                  
Rent for $95.00 / Day
                                 Buy for $2,195.95
EDCO Wedge-Less Floor Grinder
Features
GRIND WEDGE-LESS: The need for wooden wedges goes away with
EDCO’s NEW Magna-Trap™ Slide-On Tooling.
GRIND LEVEL: Using EDCO’s exclusive Leveling System Hand Wheel
you can adjust the machine’s height, use a wide range of
accessories, and truly grind level. Level grinding is quicker,
smoother, easier on the operator , and increases accessory life.
VELCRO DUST SHROUD: This new heavy-duty Velcro Dust Shroud
makes dust prevention easier. Simply readjust the shroud according
to the height of the accessory being used.
Extra Weight Standard: This bolted-on weight tray helps the
machine work.  Use when needed
Multi-Vac port for use with 2″ or 3″ vacuum hose
11″ working width will grind approximately 200-250 sq.ft. per hour at
1/32″ with EDCO Magna-Trap™ Dyma-Dots (Single)
22″ working width will grind approximately 400-500 sq.ft. per hour at
1/32″ with EDCO Dyma-Serts DDual)
Electric machine plugs into dedicated residential wall outlets
Includes 1 magnetic multi-accessory disc, which accepts Dyma-Serts,
Strip-Serts and all other Magna-Trap™ accessories. 3 grinding
accessories required per loading
EDCO’s Vortex 200 Vacuum System suppresses all the dust created
by EDCO Grinders

          $125.00/day Single
           $225.00/day Duel
             $95.00/day Vac
Set of  3 Single Dyma-Segs  $69.95
We are updating our web site; so, available
equipment and prices are subject to change
.